You are currently viewing: Articles



Jan-2019

Tray revamp restores crude column performance

Retrofitting the packed top section of a crude atmospheric tower with high capacity trays improved separation efficiency

M JAGANNATHA RAO and K SRI GANESH Hindustan Petroleum Corporation Limited
R MADHAVAN and SANDEEP YADAV Koch-Glitsch India
Viewed : 406
Article Summary
The existing crude distillation unit at Hindustan Petroleum Corporation Limited’s (HPCL) Mumbai refinery is designed to process Bombay High and Arab Mix crudes. During an earlier capacity revamp of the crude atmospheric tower, 24 conventional trays with moving valves located in the top fractionating sections that separated light naphtha, heavy naphtha, and kerosene were replaced with an equal number of Superfrac trays equipped with fixed valves. The tower configuration after the first revamp is shown in Figure 1. With Superfrac trays, capacity and separation between naphtha, heavy naphtha, and kerosene cuts were satisfactory with a good gap between the 95% ASTM D-86 distillation point of one product and the 5% ASTM D-86 distillation point of the next product. Table 1 shows the product quality of naphtha to kerosene following the first installation of Superfrac trays in the top section.

To take advantage of the opportunity to process lighter crudes, the refinery needed to overcome capacity limitations in the top fractionating sections. Plant personnel contacted an engineering company for a process study to evaluate the feasibility of achieving the 20% extra capacity needed to process lighter crudes. The engineering company recommended replacing the top section of high capacity trays with two beds of structured packing in addition to other modifications in the tower. With agreement to implement the recommended changes, the engineering company designed the structured packing and internals, which were purchased from a local fabricator. During installation, the tray tower attachments were removed to accommodate the structured packing. The tower configuration with packing revamp is shown in Figure 2. The crude capacity after the modifications could be increased by 20%, but the separation between the three cuts (light naphtha, heavy naphtha, and kerosene) was very poor with a significant overlap in the ASTM D-86 cut points as compared to the gaps that were being obtained prior to the revamp. Table 2 shows the product quality of naphtha to kerosene after the replacement of trays with packing in the top section. 
   
Analysis of the existing tower configuration
Three different evaluations were conducted: gamma scan, physical inspection of packing and internals, and a process simulation to understand the possible causes for the underperformance of the packed bed.

Gamma scan
The refinery conducted a gamma scan of the top section of the tower. The results pointed to liquid maldistribution wherein one side of the tower received a larger proportion of the liquid flow compared to the other. Critical sections, such as the equipment between two packed beds, had significant external obstructions interfering with the scan results, and consequently the data were not sufficient to accurately determine the origin of the maldistribution.

Physical inspection of the packing and internals
Two possibilities for the maldistribution were considered: the structured packing layers were not rotated at 90° angles during installation, and the tower internals may have been damaged during operation.

Structured packing layers are installed with each layer rotated 90° with respect to the layer below. The rotation mixes and spreads both liquid and vapour phases in all horizontal directions to avoid local concentration variations at the same elevation. Figure 3 shows a properly rotated stack of structured packing layers.

Structured packing with a crimp angle of 60° from horizontal with an approximate surface area of 110-115 m2/m3 was used in the fractionation section. This type of packing is more typically applied in heat transfer and absorption services and may have been selected to meet capacity requirements.

The packing and internals were inspected during a scheduled shutdown. The packing layers were found to be rotated properly, and the internals were intact. Photographs taken during shutdown indicated corrosion on the packing (Figure 4), but severe damage was absent in the sections that were accessed.

The packed beds occupied most of the tower height, and the distribution systems for liquid and vapour were fitted into a smaller vertical space. The need to maximise the packed bed height may have restricted the available space for the distribution systems. The distributor type selected by the engineering company was difficult to level and was designed to operate with a low liquid head in a multi-stage configuration. Using low liquid heads makes the distributor prone to the maleffects of liquid gradients formed by the flow and more sensitive to the levelness.

In this case, the reflux feed pipe feeding the distributor of the top bed was designed in a sub-optimal way without any significant flow restriction and could have additionally contributed to the non-uniformity of liquid distribution observed in the gamma scan. Feed pipes or pre-distribution systems are equally critical to the performance of the packed column as the liquid distributor. Obtaining the desired performance from a tower requires appropriate distribution devices for the column feeds. When designing feed or pre-distribution devices, consideration must be given to their spacing and orientation with respect to the type of liquid distributor below, expected distributor performance, flow rate, operating range, thermal condition (for instance, degree of sub-cooling), and whether mixing with overhead liquid is required. To achieve uniform liquid distribution, feed pipes should have a reasonable3 pressure drop. Restriction orifices within the pipe may be used to balance flow distribution in situations where fluid equalisation is non-ideal and it is difficult for the internals to correct for flow variations.

Vapour distribution is another important aspect in packed tower performance. Unlike trays that have significant pressure drop, packing has much lower pressure drop and is not able to correct for vapour maldistribution. Therefore, initial distribution of vapour to the packed bed is very important. In this case, the chimney collector below the top bed was installed with little space between the top of the riser to the packed bed above (see Figure 5), possibly due to the desire to maximise the packed height. It is necessary to provide sufficient3 distance between the top of the risers to the bed above to create uniformity in the vapour flow into the packed bed. The distance between the riser hats was also restrictive, creating higher velocities that would hamper good vapour distribution. The overall result of the constrained arrangement of risers beneath the packed bed is increased vapour maldistribution and reduced separation efficiency.

Process simulation
HPCL requested Koch-Glitsch to assist in improving the column performance in the packed section. Koch-Glitsch developed a steady state process model of the tower using a steady state simulation software. Ten theoretical stages were expected from the 12m of packing installed, based on efficiency data from similar size packings. However, the simulation results that matched the test run indicated that the number of stages achieved was actually less than half of the expected number.

Inside-Out revamp approach

To optimise the tower’s efficiency and capacity, Koch-Glitsch adopted the Inside-Out design approach.2 This is an iterative method that combines process simulation with equipment selection, design, and hydraulic evaluation. The benefit of this approach is that it eliminates the guesswork needed to fit the equipment design to the original simulation. For improving the packed bed performance, significant changes were envisaged for the feed pre-distribution, liquid distribution, packing selection, and vapour distribution. For the equipment design, different options were evaluated, which also included trayed options. The pros and cons of each option were identified and compared (see Table 3). Because the capacity requirement was now 20% higher than the earlier configuration of Superfrac trays, retrofitting with the original number of trays would reduce the capacity unless the tray spacing could be increased. Using higher spacing reduces the number of trays and, therefore, the number of contacting stages.
Current Rating :  3

Add your rating:



Your rate: 1 2 3 4 5