You are currently viewing: Literature



Tray design features that reduce turnaround maintenance time

Column shutdowns can be costly. Production is halted and maintenance expenses accumulate without any offsetting revenue. Maintenance crews need to isolate, open, inspect, modify, repair, and close columns, all under pressure to complete work as expeditiously as possible. Minimization of shutdown costs begins during the equipment design phase. Sulzer incorporates several features into our tray designs that can reduce column shutdown time.

Tray Replacement and Installation
Tray removal and replacement can take a significant amount of time; the larger the tray diameter, the longer the time. This is not only due to the handling the physical size of the components, but also to all the many hardware connections associated with the various tray panels.

For more than 40 years, Sulzer has offered a boltless panel to panel connection called Lip-SlotTM. This interlocking tray panel design decreases installation time by as much as 50% (two Lip- Slot trays installed in the time it normally takes to install one conventional tray).

The Lip-Slot design is used for panel to panel connection allowing adjacent panels to be quickly secured to each other. This design is typically employed on trays with diameters greater than 72 inches, where installation times can be significant. Lip-Slot design has been successfully utilized in heavy duty applications, including high uplift (2.0 PSI) internals designs.

Tray Manway Design
During column openings, it is always important to have quick access for work and inspection and then to be able to close the tray manway panels as quickly as possible. Sulzer can provide quick opening manways that allow access to the tray below in less than 10 seconds.

These quick opening manways come with handles and special locks that allow opening and closure without losing tightness between manway panels. This design allows the panels to be opened or closed either from top or bottom of the tray. The handle position indicates if it is locked or unlocked.

Some customers prefer using slide fasteners on manway panels. In these cases, an easy opening manway design has been developed with slide fasteners. This design takes somewhat longer to open and close compared with the quick opening design, but clearly less time than conventional manways.

Sponsor : Sulzer Chemtech

Other Literature

Tray designs for extreme fouling applications

Today refiners experience a lot of problems with processing of opportunity or heavy crudes. Such crudes have very high sulfur content and require the addition of amine scavengers before desalting. These amines decompose in the heater and create ammonium chlorides in the presence of water in the top of ...


Anti-fouling trays maximize coker main fractionator profitability

The Coker Main Fractionator is systematically subjected to harsh operating conditions that can lead to deteriorating efficiency and performance due to coking and fouling. Poor reliability results in loss of profitable coking margins for the refinery. The main fractionator vapor feed from the coke drum ...


Improve separation in your column by increasing the number of trays

Refiners often face revamp challenges when trying to improve separation within an existing column. Improving diesel recovery from gas oil, splitting benzene precursors from naphtha reformer charge, or simply minimizing product overlaps after capacity creep can all be difficult when limited by a fi xed ...


Gain 5-10% efficiency with this simple 4-pass tray revamp

The design of 4-pass trays can be complex. It not only requires a close evaluation of the mechanical design but also the process response to that design at various flow rates. The balancing of the fluid flows across the tray can have a substantial effect on the tray performance, namely efficiency.


Proper design of mass transfer internals in the FCC flue gas scrubber can help reduce PM emissions

The EPA’s New Source Performance Standards (40 C.F.R. §60.100-1-0, subpart Ja) regulates refinery particulate emissions, including the discharge of catalyst fines from the FCCU flue gas scrubber stack. Because refiners have traditionally correlated particulate matter (PM) emissions with FCCU ...


Improve fouling resistance in your wastewater benzene stripper

Benzene stripper columns, built so that refineries can meet the National Emissions Standards for Hazardous Air Pollutants (NESHAP), operate with several unique conditions – low vapor rates, high liquid loads, and a high tendency toward fouling make designing well-balanced, effective internals difficult.


Important tray design features that improve column operating reliability

How often does Maintenance personnel open a column during a shutdown and find tray panels fallen without any obvious damage? How about tray valves stuck in the bottoms pump suction? While the initial reaction may be to blame faulty installation where the hardware was not properly tightened, the answer ...


Green design practices: focus on efficiency

Green design is more than recycling scrap materials or calculating carbon footprints. It minimizes negative environmental impact through skillful design and operating practices to produce efficient, better-functioning processes. Because green practices reduce resource requirements, in many cases, they ...


4 simple ways to convert turnarounds into profitable tower upgrade opportunities

With planned outages commonly occurring at intervals of 2-5 years, a refinery turnaround is a prime opportunity to replace column and separator internals with the newest available technology. Planning for an outage with a “replacement-in-kind” strategy will address lost performance from refinery ...


Maximizing light cycle oil recovery in the FCC main fractionator

Refiners operating FCCU's have adjusted their operating strategies to maximize light cycle oil production to meet the increased demand for automotive diesel. Catalyst formulations and reactor conditions can alter yields, but the refinery cannot take full advantage of the increased LCO recovery without ...