You are currently viewing: Literature



Separator technology reduces refinery operating costs and downtime

A US refining company contacted us to discuss a separation problem in the feed to an alkylation process. Caustic entrainment from their selective hydrogenation unit was poisoning the hydrofluoric acid catalyst in the alkylation unit. The continuous phase feed to the alkylation unit consisted of ~180m3/hr of mixed C4 hydrocarbons, mainly butanes and butylenes, with varying levels of 10 – 20% caustic solution entrained as a dispersed aqueous phase.

Sulzer was commissioned to design, engineer and manufacture a solution to the problem which would reduce the caustic entrainment to less than 30 ppmv.

The Solution
Examination of the process upstream of the alkylation reactor revealed that separation of the caustic entrainment should have occurred in a gravity separator. Calculations suggested that the gravity separator would be capable of droplet removal down to about 60 microns. However, the low interfacial tension in the hydrocarbon/caustic system was likely to result in much more finely dispersed droplets and coalescer internals were therefore recommended.

Originally planned as a retro-fit project for the gravity separator, the customer decided that potential contamination with hydrofluoric acid presented too many safety issues and a decision was made to replace the vessel with a new skid-mounted coalescer complete with prefilters and caustic flash drum.

The main feature of the package was a 78” diameter horizontal separator vessel complete with Enhanced DC CoalescerTM internals and Enhanced flow distribution device.

The Enhanced DC Coalescer was manufactured as a co-knit composite packing of 316L SS and special multifilament fluoro-polymer fiber (PTFE). The combination of materials with different surface free energies provides accelerated rates of droplet coalescence at each of the thousands of point contacts between the materials – a property of the Sulzer DC Coalescer originally patented by KnitMesh Ltd (now a part of Sulzer Chemtech). The use of the fibrous PTFE multifilament provides exceptional direct interception efficiency for very small droplets, allowing them to accumulate, coalesce and eventually drain to the bulk phase interface in the boot of the vessel.

Two prefilters with 10 micron cut-off size were provided as part of the package to protect the coalescer from particulate contamination in the feed.

Results: The complete package was engineered, manufactured and delivered within a 15 week lead time. Installation of the equipment has reduced the entrainment levels from the original 10-20% to the target levels of < 30 ppmv providing the operator with substantial benefits in terms of:
- Reduced downtime
- Increased catalyst life
- Reduced catalyst cost

Other Literature

Tray designs for extreme fouling applications

Today refiners experience a lot of problems with processing of opportunity or heavy crudes. Such crudes have very high sulfur content and require the addition of amine scavengers before desalting. These amines decompose in the heater and create ammonium chlorides in the presence of water in the top of ...


Anti-fouling trays maximize coker main fractionator profitability

The Coker Main Fractionator is systematically subjected to harsh operating conditions that can lead to deteriorating efficiency and performance due to coking and fouling. Poor reliability results in loss of profitable coking margins for the refinery. The main fractionator vapor feed from the coke drum ...


Improve separation in your column by increasing the number of trays

Refiners often face revamp challenges when trying to improve separation within an existing column. Improving diesel recovery from gas oil, splitting benzene precursors from naphtha reformer charge, or simply minimizing product overlaps after capacity creep can all be difficult when limited by a fi xed ...


Gain 5-10% efficiency with this simple 4-pass tray revamp

The design of 4-pass trays can be complex. It not only requires a close evaluation of the mechanical design but also the process response to that design at various flow rates. The balancing of the fluid flows across the tray can have a substantial effect on the tray performance, namely efficiency.


Proper design of mass transfer internals in the FCC flue gas scrubber can help reduce PM emissions

The EPA’s New Source Performance Standards (40 C.F.R. §60.100-1-0, subpart Ja) regulates refinery particulate emissions, including the discharge of catalyst fines from the FCCU flue gas scrubber stack. Because refiners have traditionally correlated particulate matter (PM) emissions with FCCU ...


Improve fouling resistance in your wastewater benzene stripper

Benzene stripper columns, built so that refineries can meet the National Emissions Standards for Hazardous Air Pollutants (NESHAP), operate with several unique conditions – low vapor rates, high liquid loads, and a high tendency toward fouling make designing well-balanced, effective internals difficult.


Important tray design features that improve column operating reliability

How often does Maintenance personnel open a column during a shutdown and find tray panels fallen without any obvious damage? How about tray valves stuck in the bottoms pump suction? While the initial reaction may be to blame faulty installation where the hardware was not properly tightened, the answer ...


Green design practices: focus on efficiency

Green design is more than recycling scrap materials or calculating carbon footprints. It minimizes negative environmental impact through skillful design and operating practices to produce efficient, better-functioning processes. Because green practices reduce resource requirements, in many cases, they ...


4 simple ways to convert turnarounds into profitable tower upgrade opportunities

With planned outages commonly occurring at intervals of 2-5 years, a refinery turnaround is a prime opportunity to replace column and separator internals with the newest available technology. Planning for an outage with a “replacement-in-kind” strategy will address lost performance from refinery ...


Maximizing light cycle oil recovery in the FCC main fractionator

Refiners operating FCCU's have adjusted their operating strategies to maximize light cycle oil production to meet the increased demand for automotive diesel. Catalyst formulations and reactor conditions can alter yields, but the refinery cannot take full advantage of the increased LCO recovery without ...