Flow metering vacuum tower bottoms

A clamp-on ultrasonic flow meter can make flow measurement at the bottom of vacuum distillation towers more reliable

Rainer Wetzel

Viewed : 7083

Article Summary

Operating at temperatures of around 350°C, the bottom of a vacuum distillation tower is no place for delicate instrumentation. To measure the flow rate of vacuum residue or bitumen, refiners therefore traditionally rely on differential pressure (DP) devices such as orifice plates or venturis. These are simple, robust and economical in line sizes above 200 mm.

Unfortunately, simplicity and robustness do not always imply accuracy or reliability. The biggest problem with all DP devices is the need for a pair of impulse lines connecting the sensor to the DP transmitter. Impulse lines often become plugged with particles of solid material such as coke or bubbles of gas. In bitumen service, blockages are most commonly due to frozen product — a particular problem in cold climates, despite trace heating.

Faced with unreliable orifice plates, one refiner sought a better way to measure the flow of bitumen leaving a vacuum tower on its way to a delayed coker. In this case, the product starts life as crude bitumen, which is diluted with lighter hydrocarbons to create a synthetic crude. The lessons learned, however, apply equally well to refined bitumen produced in the vacuum distillation of conventional crude.

Clamp-on flow meter
The refining company decided to try a clamp-on ultrasonic flow meter as a way to make flow measurement more reliable. The main rationale for the experiment was that because ultrasonic flow meters are non-
invasive and do not require impulse lines, they cannot become clogged or blocked. Other important features of this flow measurement principle are that it is independent of system pressure, works with practically any fluid and remains accurate over a wide turndown range.

The company first carried out several tests with a portable ultrasonic flow meter, allowing it to select the best transducer type and positions for the job in hand. Once the engineers were confident that the new technology would perform well, they installed a permanent clamp-on ultrasonic flow meter on the 400 mm pipework connected to the bottom of the vacuum tower.

The complete system comprised two sets of Flexim Type G low-frequency ultrasonic transducers with high-temperature mountings and a Fluxus ADM 7407 transmitter with two input channels. The transmitter communicates with the refinery’s distributed control system (DCS), making it easy to compare the readings from the ultrasonic flow meter with those of the flow transmitters linked to the three original orifice plates (see Figure 1).

Trial performance
The trial took place from December 2008 to April 2009. Figure 2 represents a period of 24 hours and shows that the Flexim flow meter (A, red line) provided reliable and consistent readings, albeit with short-term spikes caused by the presence of gas bubbles. Orifice plate B (green), in contrast, was noisy and unreliable due to problems with freezing of the impulse lines. Ignoring noise, the readings from the ultrasonic flow meter agreed well with those from orifice plate B.

The flow rate as calculated by subtracting the reading of orifice plate D (light blue) from that of orifice plate C (dark blue, see Figure 1) was consistently higher by around 10% (44 bbl/h) than that measured by the Flexim flowmeter and orifice plate B. The accuracy of the Flexim flow meter under ideal conditions is ±1.6% of reading; the trial did not attempt to establish its accuracy under real plant conditions, but this is likely to be considerably better than that of an orifice plate and DP transmitter.

The same comparison over the first month of the trial is shown in Figure 3. The reading from the ultrasonic flow meter shows spikes, occasionally very large, due to gas bubbles, but it is clearly more reliable and stable than the measurements from orifice plates B and C.

Figure 4 shows the results for another one-month period, this time between 15 March and 15 April. By the beginning of April, ambient temperatures are above freezing and the stability of the readings from orifice plates B and C improves accordingly. Regardless of temperature, however, the Flexim flow meter is more stable than either of the two main orifice plates.

Permanent placement
By the end of the trial, the refiner was sufficiently impressed with the ultrasonic flow meter to make it a permanent installation, further increasing measurement reliability and reducing maintenance costs.

The company concluded that for bitumen and high-temperature service, the Flexim clamp-on ultrasonic flow meter is more reliable than an orifice plate with a DP transmitter. This is especially so during freezing weather, when impulse lines are particularly likely to block. The fact that it can be installed without shutting down the process makes the ultrasonic flow meter suitable for retrofitting to existing plants.

How ultrasonic flow meters work
Ultrasonic flow meters use beams of high-frequency sound to measure the velocity of moving fluids. Two types are available: Doppler and transit time.

Doppler flow meters measure the frequency shift that occurs when ultrasound is reflected by bubbles or particles in the moving fluid —the same principle as a radar speed gun. Transit-time (time-of-flight) flow meters rely on the fact that the apparent velocity of ultrasound waves through the fluid depends on whether they are travelling with or against the direction of flow. The ultrasound transmitter and receiver can be mounted on opposite sides of the pipe, or on the same side; in the second case, they are arranged so that the ultrasound reflects off the far wall of the pipe. Alternate ultrasound pulses travel in opposite directions: once with the flow and once against it.

Add your rating:

Current Rating: 2

Your rate:

  • Responsive image Worldwide refinery processing review
  • Responsive image Becht fired heaters services
  • Responsive image Valves and Pumps for the Energy Industry
  • Responsive image BASF Refinery Solutions on LinkedIn
  • Responsive image Data governance consulting services
  • Responsive image ITW technologies online cleaning
  • Responsive image Air grid nozzles for fluid catalytic cracking units
  • Responsive image Custom Catalysts
  • Responsive image Reciprocating compressor solutions for refineries
  • Responsive image RVP in process